Parameter no. 1 – Relay contact type

Defines the contact type when open/closed contact.

Values (size is 1-byte dec):

• Default value 0
• 0 – NO (normally open) output type
• 1 – NC (normally close) output type

Parameter no 3. – turning off alarming

Values (size is 1-byte dec):

• Default value 1
• 0 – only by the Z-Wave command (basic set, switch multilevel set, switch multilevel start/stop level change, switch color set, switch color start/stop level change, notification report idle)
• 1 –  capacitive input (up, down, left, right) or z-wave command (basic set, switch multilevel set, switch multilevel start/stop level change, , switch color set, switch color start/stop level change, notification report idle)

Parameter no. 10. – auto on timer

Defines the time after which the device is turned to last known state.

Values (size is 1-byte dec):

• Default value 0
• 0 – disabled
• 30 – 32535 = 30 – 32535 seconds after which the device turns on

Parameter no. 11. – auto off timer

Values (size is 2-byte dec):

Defines the time after which the device is turned to last known state.

• Default value 0
• 0 – disabled
• 30 – 32535 = 30 – 32535 seconds after which the device turns off

Parameter no. 30. – restore state on power failure

Values (size is 1-byte dec):

• Default value 1
• 1 – enabled (the device will restore state on power failure)
• 0 – disabled (the device will not restore state on power failure and will remain off)

Parameter no. 31. – restore relay state on power failure

Values (size is 1-byte dec):

• Default value 1
• 1 – enabled (the device will restore state on power failure)
• 0 – disabled (the device will not restore state on power failure and will remain off)

Parameter no. 40 – Watt Power Consumption Reporting Threshold for Load

Choose by how much power consumption needs to increase or decrease to be reported. Values correspond to percentages so if 10 is set (by default), the device will report any power consumption changes of 10 % or more compared to the last reading.

Values (size is 2-byte dec):

• Default value 10
• 0 – Power consumption reporting disabled
• 1 – 100 = 1 % – 100 % Power consumption reporting enabled. New value is reported only when Wattage in real time changes by more than the percentage value set in this parameter compared to the previous Wattage reading, starting at 1 % (the lowest value possible).

NOTE: Power consumption needs to increase or decrease by at least 1 Watt to be reported, REGARDLESS of percentage set in this parameter.

Parameter no. 42 – Watt Power Consumption Reporting Time Threshold for Load

Set value refers to the time interval with which power consumption in Watts is reported (0 – 32535 seconds). If 300 is entered (by default), energy consumption reports will be sent to the gateway (hub) every 300 seconds (or 5 minutes).

Values (size is 2-byte dec):

• Default value 0
• 0 – Power consumption reporting disabled
• 30 – 32535 = 30 – 32535 seconds. Power consumption reporting enabled. Report is sent according to time interval (value) set here.

Parameter no. 60 – Lock touch for relay only

This parameter enables ONLY the touch functionality for closing/opening the relay meant for switching ON/OFF the connected light or any other connected load. See chapter 5.4 for additional information.

Values (size is 1-byte dec):

• Default value 0
• 0 – disabled
• 1 – enabled (the user can switch ON/OFF the connected light or any other connected load by touching ANY button. Other functionalities (lighting mode, scenes, dimming and full white, inclusion/exclusion and reset) are unavailable until function disabled).

Parameter no. 70 – Overload safety switch

The function allows for turning off the controlled device in case of exceeding the defined power for more than 5 sec. Controlled device can be turned back on by capacitive antenna/s or sending a control frame.

Values (size is 2-byte dec):

• Default value 2300
• 0 = function not active
• 1 – 2300 = 1 W – 2300 W

ⓘ NOTE: This functionality is not an overload safety protection, please check chapter “Functionalities” for more details.

In case of overload the following message will be send towards the controller:

COMMAND_CLASS_NOTIFICATION_V5

The Alarm V1 type field set to 0x00

Notification Type 0x08 and 0x08 (Overload detected)