Smart Plug 16A - Technical specifications | Qubino
Where to buy

Smart Plug 16A – Technical specifications

Technical specifications

Power supply 230 VAC ±10% / 50-60Hz
Power load 16A resistive max.
Overload protection > 16A
Power consumption < 1W
Housing dimensions 43 x 52 x 75 mm
Package dimensions 70 x 70 x 55,5 mm
Housing colour white
Weight (ex. Packaging) ~ 80g
Weight with packaging ~ 101g
Z-Wave operation range up to 30 m indoors (98 ft)
Operating temperature 0 ~ +40°C (32 ~ 104°F); <80% RH non-condensing
Storage operation -20 ~ +70°C
(-4 ~ 158°F);
<80% RH non-condensing
Plug & Socket type Plug Type F, Socket
compatible with type C and F
Switching Relay
IP 20
Repeater Yes
Power measurement accuracy ±2%
Current measurement accuracy ±1%
Energy measurement accuracy ±2%
Voltage measurement accuracy ±1%

Supported Z-Wave Frequencies

 

ORDERING CODE FREQUENCY
ZMNHYD1 868.4 MHz
ZMNHYD4 869,0 MHz
ZMNHYDA 919,7 - 921,7 - 923,7 MHz
ZMNHYDB 868,1 MHz
ZMNHYDE 920,9 MHz

Smart Meter is supporting 50/60Hz power supply frequency.

Configuration Parameters

Z-Wave Parameter 11

Parameter no. 11 - Turn Smart plug 16A Off Automatically with Timer

If Smart plug 16A is ON, you can schedule it to turn OFF automatically after a period defined in this parameter. The timer is reset to zero each time the device receives an ON command, either remotely (from the gateway (hub) or associated device) or locally from the switch.

Values (size is 2 byte dec):

  • default value 0
  • 0 - Auto OFF Disabled
  • 1 - 32535 = 1 - 32535 seconds. Auto OFF timer enabled for a given number of seconds.

Parameter no. 12 - Turn Smart plug 16A On Automatically with Timer

If Smart plug 16A is OFF, you can schedule it to turn ON automatically after a period of time defined in this parameter. The timer is reset to zero each time the device receives an OFF command, either remotely (from the gateway (hub) or associated device) or locally from the switch.

Values (size is 2 byte dec):

  • default value 0
  • 0 - Auto ON Disabled
  • 1 - 32535 = 1 - 32535 seconds. Auto ON timer enabled- for a given amount of seconds

Parameter no. 30 - Restore on/off status for Smart plug 16A after power failure

This parameter determines if on/off status is saved and restored for the Smart plug 16A after power failure.

Values (size is 1 byte dec):

  • default value 0
  • 0 - Device saves last on/off status and restores it after a power failure
  • 1 - Device does not save on/off status and does not restore it after a power failure, it remains off

Parameter no. 40 – Watt Power Consumption Reporting Threshold for Smart plug 16A

Choose by how much power consumption needs to increase or decrease to be reported. Values correspond to percentages, so if 20 is set (by default), the device will report any power consumption changes of 20% or more compared to the last reading.

Values (size is 1 byte dec):

  • default value 20
  • 0 - Power consumption reporting disabled
  • 1 - 100 = 1% - 100% Power consumption reporting enabled. New value is reported only when Wattage in real time changes by more than the percentage value set in this parameter compared to the previous Wattage reading, starting at 1% (the lowest value possible)

Power consumption needs to increase or decrease by at least 1 Watt to be reported, REGARDLESS of percentage set in this parameter.

NOTE: When reporting Watts, module will automatically report also [V] (Voltage) and [A] (Amperes)

Parameter 42 - Qubino

Parameter no. 42 – Watt Power Consumption Reporting Time Threshold for Smart plug 16A Load

Set value refers to the time interval with which power consumption in Watts is reported (30 – 32535 seconds).

Values (size is 2 byte dec):

  • default value 0
  • 0 - Power consumption reporting on time interval disabled
  • 30 - 32535 = 30 - 32535 seconds. Power consumption reporting enabled. Report is sent according to time interval (value) set here

The device is reporting the following values (if there was a change): W, V and A.

NOTE: The energy consumption (kWh) is reported regardless of the values, set in the parameters 40 and 42. The energy consumption will be reported, when it increases for at least 0,1 kWh.

Parameter 50 - Qubino

Parameter no. 50 – Down value

Lower power threshold used in parameter no. 52.

Values (size is 2 byte dec):

  • default value 30 = 30 W
  • 0 – 4000 = 0W – 4000 W

Down value cannot be higher or equal to the value specified in parameter no. 51. If the set value is higher or equal to the value in parameter 51, the set command is ignored.

NOTE: if parameter no. 50 value is 100W, if measured power is lower than 100W, the association is sent.
Power threshold step is 1W.

Parameter 51 - Qubino

Parameter no. 51 – Up value

Upper power threshold used in parameter no. 52

Values (size is 2 byte dec):

• default value 50 = 50 W
• 0 – 4000 = 0 W – 400 W

Up value cannot be lower or equal to the value specified in the parameter no. 50. If the set value is lower or equal to the value in parameter 50, the set command is ignored.

NOTE: If parameter no. 51 value is 200W. If measured power is higher than 200W the association is sent.

Power threshold step is 1W.

Parameter 52 - Qubino

Parameter no. 52 - Action in case of exceeding defined power values (parameters 50 and 51)

PParameter defines the way 3rd association group devices are controlled, depending on the current power load.

Values (size is 1 byte dec):

• default value 6
• 0 – function inactive
• 1 – turn the associated devices on, once the power drops below Down value (parameter no. 50)
• 2 – turn the associated devices off, once the power drops below Down value (parameter no. 50)
• 3 – turn the associated devices on, once the power rises above Up value (parameter no. 51)
• 4 – turn the associated devices off, once the power rises above Up value (parameter no. 51)
• 5 – 1 and 4 combined. Turn the associated devices on, once the power drops below Down value (parameter no. 50). Turn the associated devices off, once the power rises above Up value (parameter no. 51).
• 6 – 2 and 3 combined. Turn the associated devices off, once the power drops below Down value (parameter 50). Turn the associated devices on, once the power rises above Up value (parameter no. 51).

Parameter 70 - Qubino

Parameter no. 70 - Overload safety switch

The function allows for turning off the controlled device in case of exceeding the defined power for more than 3 seconds. Controlled device can be turned back on by S-button or sending a control frame. By default this function is inactive.

Values (size is 2 byte dec):

• default value 0
• 1 – 4000 = 1 W – 4000W
• 0 = function not active

NOTE: This functionality is not an overload safety protection, please check installation note for details.

IIn case of overload the following message will be send towards the controller:

• COMMAND_CLASS_NOTIFICATION_V5
• The Alarm V1 type field set to 0x00
• Notification Type 0x08 and 0x08 (Overload detected)

NOTE: Regardless of the value set in this parameter the overcurrent protection is always active and can not be disabled.

Parameter no. 71 – Power threshold

This function allows setting the power threshold for triggering the Program started notification. When the threshold is reached, the notification will let the user know that the device connected to the smart plug started working.

Values (size is 2 byte dec):

• default value 0
• 1 – 4000 = 1 W – 4000W
• 0 = function not active

When the threshold is reached the following message will be send towards the controller:

IIn case of overload the following message will be send towards the controller:

• COMMAND_CLASS_NOTIFICATION_V5
• The Alarm V1 type field set to 0x00
• Notification Type 0x0C and 0x01 (Program started)

Parameter no. 72 – Time interval

This function allows setting the time interval for triggering the Program completed notification. When the active power will fall below the power threshold set in parameter 71, the time interval will start and when it will expire the notification will let the user know that the device connected to the smart plug finished working. The time interval is useful for the devices that have pause intervals during operations.

Values (size is 1 byte dec):

• default value 1
• 0 – 125 = 0 – 125 minutes
• 0 = immediate sending of notification when active power drops below the threshold set in the parameter 71

When the time interval expires the following message will be send towards the controller:

• COMMAND_CLASS_NOTIFICATION_V5
• The Alarm V1 type field set to 0x00
• Notification Type 0x0C and 0x03 (Program completed)

Parameter no. 73 – Turn Smart Plug OFF

This function allows turning the Smart Plug output to OFF once the time interval is expired and the Program completed notification is sent to the controller.

Values (size is 1 byte dec):

• default value 0
• 0 – function disabled
• 1 – turn OFF relay once the notification Program completed is sent

Parameter no. 74 – Enable/disable LED

This function allows enabling or disabling the Smart Plug LED. In case the user doesn’t want the LED indicator, it can be turned OFF with this parameter.

NOTE: if an overload or overcurrent occurs the red LED will still turn ON regardless of the value set in this parameter.

Values (size is 1 byte dec):

• default value 1
• 0 – LED is disabled
• 1 – LED is enabled

Electrical diagram

S Service button (used to add or remove device from the Z-Wave network)
LED1 When the Smart Plug 16A is excluded:
When the relay is turned OFF:
- blue LED is blinking (1 sec ON, 1 sec OFF)
When the relay is turned ON:
- blue LED is ON
- red LED is blinking (0.3 sec ON, 0.3 sec OFF) when the current exceeds 14,4A
- red LED is ON after the overload occurred
When the Smart Plug 16A is included:
When the relay is turned OFF:
- LED is off
When the relay is turned ON:
- blue LED is ON
- red LED is blinking (0.3 sec ON, 0.3 sec OFF) when the current exceeds 14,4A
- red LED is ON after the overload occurred

Package content

1 device + 1 user manual
Practical blister packaging ensures lower cost of delivery.
Package dimensions (WxHxD): 70 x 70 x 55,5 mm
Gross weight (ex. packaging): 101g