Smart Meter – Technical specifications

Parameter no. 7 – Input 1 switch function selection

Available configuration parameters (data type is 1 Byte DEC):

• default value 4
• 0 – disabled
• 2 – IR external relay control – mono stable push button
• 3 – IR external relay control – bi stable switch
• 4 – External relay control – mono stable push button
• 5 – External relay control – bi stable switch

Parameter no. 11 – Automatic turning off IR external relay output after set time

When External IR relay is ON it goes automatically OFF after time defined in this parameter. Timer is reset to zero each time the device receives ON command.
Values (size is 2 byte dec):

• Default value 0
• 0 = Auto OFF disabled
• 60-32535 = 60 seconds – 32535 seconds

 

Parameter no. 12 – Automatic turning on IR external relay output after set time

When External IR relay is OFF it goes automatically ON after time defined in this parameter. Timer is reset to zero each time the device receives OFF command.

Values (size is 2 byte dec):

• default value 0
• 0 – Auto ON disabled
• 60-32535 = 60 seconds – 32535 seconds

Parameter no. 13 – Automatic turning off External relay output after set time

When External IR relay is ON it goes automatically OFF after time defined in this parameter. Timer is reset to zero each time the device receives ON command.

Values (size is 2 byte dec):

• Default value 0
• 0 = Auto OFF disabled
• 60-32535 = 60 seconds – 32535 seconds

Parameter no. 14 – Automatic turning on External relay after output set time

When External IR relay is OFF it goes automatically ON after time defined in this parameter. Timer is reset to zero each time the device receives OFF command.

Values (size is 2 byte dec):

• Default value 0
• 0 = Auto ON disabled
• 60-32535 = 60 seconds – 32535 seconds

Parameter no. 40 – Power reporting in Watts on power change

Set value means percentage, set value from 0 – 100 = 0 % – 100 %. Available configuration parameters (data type is 1 Byte DEC):

• • default value 10
  • 0 – reporting disabled
  • 1 – 100 = 1 % – 100 % Reporting enabled. Power report is sent (pushed) only when actual power in Watts in real time changes for more than set percentage comparing to previous actual power in Watts, step is 1 %.

NOTE: If power changed is less than 1 W, the report is not sent (pushed), independent of percentage set. When reporting Watts, device will automatically reports also V (Voltage), A (Amperes), Power factor, kVar (Reactive Power).

Parameter no. 42 – Power reporting in Watts by time interval

Set value means time interval (0 – 32535) in seconds, when power report is sent. Available configuration parameters (data type is 2 Byte DEC):

• default value 0
• 0 – Reporting Disabled
• 60 – 32535 = 60 second – 32535 seconds. Reporting enabled, Power report is sent with time interval set by entered value. When reporting Watts, device will automatically reports also V (Voltage), A (Amperes), Power factor, kVar (Reactive Power).

Parameter no. 45 – Reset Power counters

Available configuration parameters (data type is 1 Byte DEC):

• default value 0
• 0 – no function
• 1 – reset counter 1 – KWh
• 2 – reset counter 2 – kVARh
• 4 – reset counter 3 – kVAh
• 15 – reset ALL counters

Parameter no. 100 – Enable / Disable endpoints IR external relay (BICOM) and TRIAC External relay (IKA)

Enabling IR external relay (BICOM) and Triac External relay (IKA) or both of them, means that endpoint (IR external relay) and endpoint (External relay) or both will be present on UI. Disabling them will result in hiding endpoints according to Parameter set value. Note that hiding endpoint has no impact on its functionality.

Values (size is 1 byte dec):

• default value 0
• 0 – Endpoints IR external relay and External relay disabled
• 1 – Endpoints IR external relay (BICOM) enabled, Triac External relay (IKA) disabled
• 2- Endpoints IR external relay (BICOM) disabled, Triac External relay (IKA) enabled
• 3- Endpoints IR external relay and External relay enabled

NOTE1: After parameter change, first exclude device (without setting parameters to default value) and then re include the device.

NOTE 2: If you don’t have IR BICOM relay device mounted and you enable IR communication (parameter 100 is 2 or 3) there will be no valid IR relay state reported. It will be reported IR COMMUNICATION ERROR and LED2 will BLINK.

Parameter no. 110 – Maximum Power auto off

Set value means Maximum Power Consumption (0 – 15000) in watts (W), when relays are turned off according to parameters no. 111 and 112.

Values (size is 2 byte dec):

• default value 0
• 0 – no function
• 1 – 15000 = 1 W – 15000 W (Maximum Power Consumption)

Parameter no. 111 – Delay overpower off

Set value means number of second to power off relay (defined by parameters no. 110 and 112) before restart (30 – 32535) in seconds (s).

Values (size is 2 byte dec):

• default value 30
• 30 – 32535 = 30 s – 32535 s delay

Parameter no. 112 – Relay to power off

Set value selects relay to be powered off when threshold is reached (defined by parameters no. 110 and 111).

Values (size is 1 byte dec):

• default value 0
• 0 – switch between the 2 relays (power off relay 1 first, after power on, if power consumption is still over, power off relay 2, …)
• 1 – always power off relay 1 (IR external relay)
• 2 – always power off relay 2 (External relay)
• 3 – always power off both relays (relay 1 and relay 2)